25
Apr
Install the self adjuster lever onto the star adjuster. Remove the brake drum and turn the adjuster to push the brake shoes slightly further apart then re-fit the brake drum over the shoes and wheel studs.
Replace the brake shoe retaining pin on both brake shoes turning it ninety degrees to secure it.
Drum brake shoes replacement. Bosch BS704R Blue Drum Brake Shoe Set for Ford. 1995-09 B2300 1998-01 B2500 1995-07 B3000 1995-09 B4000 - REAR 37 out of 5 stars 4 Automotive. Bosch BS589 Blue Drum Brake Shoe Set for Toyota.
1987-00 4Runner 1987-94 Pickup 1993-98 T100 1995-02 Tacoma 2000-03 Tundra - REAR 46 out of 5 stars 106 1990. The brake shoes are spread apart by the wheel cylinder and the friction material on the outside of the brake shoes presses against the brake drum and stop your vehicle. Over time the friction material wears down leaving only the metal frame of the brake shoe which makes noise when it contacts the drum.
Brake shoes are found only at the rear wheels in cars with a drum brake system. When you step on the brake pedal brake shoes press against the brake drums to cause friction that slows down the car. Brake shoes usually last twice as long as brake pads.
Replacing rear drum brakes shoes drums and hardware in an average car in a repair shop costs from 420 to 750 per axle. Brakes are replaced on both sides at the same time. Drum brake in a car.
If you plan on changing your drum brakes yourself make sure to follow manufacturers instructions and safety precautions. The drums only need replacing if they are deeply cracked or oversize. Properly adjusted drums last for several sets of shoes.
The inner edge will need to be cleaned and gently chamfered off to allow the drum to slide back on easily when refitting. When youre ready to replace your drum brakes remove your hubcap and loosen the lug nuts to get started. Then spray the hub with a penetrating oil like PB Blaster and pull the drum off.
Place the whole drum in a container and spray it with brake cleaner. Replacing the iron brake drums is expensive as there is a significant amount of labor involved and the parts themselves will cost on average 100. The full brake drum replacement cost averages between 250 and 350.
The price may vary as front and rear drum brake replacement costs will involve different parts and labor times. If the damage to the brake drum is bad enough it will begin to cause problems with the brake shoes. In most cases brake drums will be replaced in pairs due to the issues that have one new and one worn drum can cause.
Learn how to replace your drum brakes including the wheel cylinder and bleeding the brakes. This is the only video you need to watch. Remove the brake drum and turn the adjuster to push the brake shoes slightly further apart then re-fit the brake drum over the shoes and wheel studs.
Repeat step 3 until the brake drum slides over the shoes as it is pushed into place - ie. It will be tight but movable - you should not feel that you are forcing it into place. Replace the brake shoe retaining pin on both brake shoes turning it ninety degrees to secure it.
Install the lower brake spring between the two shoes. Install the self adjuster lever onto the star adjuster. Install the brake spring on the left side of the assembly between the self adjuster lever and the bottom of the brake shoe.
To replace the brake shoes will first need to be discharged from the brake drum itself often using a brake drum removal tool. Next the wheel is removed which then allows the drum to slip off the lug posts and the shoes. Regardless of the cause for replacement we can supply you with drum brake shoes that will restore OE braking performance.
The friction material is engineered for each application so you get stopping power that suits your driving needs. Temperatures inside a brake drum can gradually fatigue brake hardware. Why you should inspect and replace brake shoes.
Worn shoes can dramatically reduce your braking system s stopping power and lead to dangerous increased stopping distances. Ignoring worn shoes can also lead to more expensive repairs such as grooved brake drums that will also have to be replaced. Brake Shoe Replacement Brake shoe linings are made from different heat resistant materials mixed with compounds such as brass ceramic and graphite.
This lining can be riveted or glued to the shoe. These materials have replaced the asbestos linings manufactured in the past. You have two brake shoes inside each brake drum held in place by a series of pins springs and brackets.
There is a pair of pins one on either side of the assembly that will need to be removed first. These pins are spring loaded. Using a pair of pliers press the spring on one of the pins in then rotate the pin from the back with your hand.