26
Aug
Each DanaSpicer unit has a unique inspection cover and gasket shape. Dana front and rear differentials can be found most commonly in Jeep Ford and Dodge vehicles.
Referred to internally as the Fat Boy the Dana Super 60 evolved from the 78-79 Dana 60 front axle first found under Ford F-250 and F-350 trucks.
Dana 60 front axle identification. All Dana axles have a Bill of Materials BOM number stamped into the long axle tube that can be used to look up many of the axles important details including the gear ratio ring gear rotation differential type and spline count as well as a complete list of replacement parts. Dana 60 View Parts. 610295-3 Front 410 Standard Low 410.
The original factory axles in a Full Float Dana 60 always have 30 splines or less. If you pull an axle shaft out of your Dana and it has 33 or 35 splines then you probably have a Dana 70. We say probably because its possible that your Dana 60 could have upgraded axle shafts installed by a prior owner with more than 30 splines.
To find the complete build details of any Dana 60 axle locate the BOM number stamped into the long axle tube and then find that code in the table below. Measure Your Axle If all else fails and youre sure its either a Dana 44 or a Dana 60 you can measure the differential cover to identify your Dana axle. Although the Dana 44 and Dana 60.
The DanaSpicer Model 60 is an automotive axle manufactured by Dana Holding Corporation and used in OEM pickup and limited passenger car applications by Chevrolet Dodge Chrysler Jeep Ford and Land RoverThere are front and rear versions of the Dana 60. It can be readily identified by its straight axle tubes 10 bolt asymmetrical cover and a 60 cast in to the housing. All of these axles take different parts so we need to properly identify the axle you have to get the right part.
AMC JEEP FRONT AXLES. Find your AMCJeep vehicle in the chart below and click on the illustration for a larger view. Dodge with Dana 60.
CB300 CB400 D300-D600 M300-M500 MB400 W300-W400 WM300 P300. Dana Differential Identification Specs. Dana is the stock differential for a large segment of domestic cars trucks and SUVs.
Dana front and rear differentials can be found most commonly in Jeep Ford and Dodge vehicles. The Bill of Material BOM number is used to identify Dana differentials. The BOM will identify the model number the gear ratio the type of differential and all component parts.
Traditional BOMs are 6 digits followed by 1 or 2 digits and start with the numbers 60 or 61. How To Identify A Dana Spicer Axle The Bill of Material number may also be found on the carrier in some models as shown in illustration 2A. For independent front suspension IFS axles the BM number may be located at one of three locations.
Referred to internally as the Fat Boy the Dana Super 60 evolved from the 78-79 Dana 60 front axle first found under Ford F-250 and F-350 trucks. The Dana 60 can be identified by the bill of material BOM numbers stamped on the axle housing. The date of production is the first set of numbers stamped to the right of the differential.
The next set of numbers to the right contain the BOM information. The Bill of Material BOM number is used to identify Dana differentials. The Dana axle identification BOMs are six digits long and begin with the number 60 or 61 followed by 1 or 2 digits such as 605561-1.
Later-model Dana axle identification charts may start off with the first three digits of 200 rather than 60 or 61 for example 200561-1. Below is a list of various BOM numbers. Ranger BOMs are listed at the bottom of the page.
Also check out our How To Identify Dana Axles page. Complete Bill Of Material information. Bill of Material Number - Manufacturer - Model - Front Rear - Application 603470 JEEP 60 REAR 1979 J20 PICKUP 60.
Rebuilt GM Ford Dana 60 Front Axles. Gear Ratio changes from 373 to 488 - Installed 37500 Gear Ratio changes from 513 Up - Installed 39500 Lock Rite - Installed 46900 TruTrac Limited Slip - Installed 98500 Detroit Locker - Installed 89500. The Dana 30 will only be found as a Jeep front axle while the Dana 35 will only be found as a rear axle on Wranglers.
Dana 35 axles have earned a very poor reputation in the off-roading world however it is a great axle for stock Wranglers. If you intend on running 33 inch or larger tires on your Wrangler make sure you have a Dana 44. New Listing 1978-1997 Ford F-350 Dana 60 Front Axle Wheel Hubs - 8 Lug - 8x65 Bolt Pattern.
Dana 25 27 Front. When modifying a Jeep the Dana 60 is popular for racing and serious off-roading. While its not a stock option in the Wrangler family they are used on 34 and 1-ton pickup trucks.
A collection of quick tips on how to identify some of the more common types of differentials and an overview of the different styles of axles you may find u. Each DanaSpicer unit has a unique inspection cover and gasket shape. Compare the gasket shape to Nationwide Parts Axle Identification Chart to determine the Dana model number.
Dana models 25 27 30 60 70 and 80 have identical gasket shapes and bolt counts and therefore must be identified by locating the identification tag.